Cable blowing machines · Made in Italy

Looking for "drill powered optical fibre cable blowing machine"?

From last-mile connections to long-distance runs, a Fibernet technician can help you choose the right machine for your fiber optic cable installation.

Expert advice direct from the manufacturer / Free demonstration on request

Some of our customers.

Keep your installation moving with Fibernet cable blowing machines.

On-site training
US & Worldwide Technical support
Spare parts ready to ship
Replacement machine if yours breaks down

Photos and stories from installers, published by Fibernet.

Cable blowing machines in action.

Three installers testing the Opera cable blowing machine on siteEnlarge +
Opera with the installers on site.
A Fibernet technician showing installers how to use the cable blowing machineEnlarge +
Hands-on demonstration with a Fibernet technician.
Close-up of a Geniale cable blowing machine during an outdoor testEnlarge +
A closer look at Geniale in the field.
GoogleExcellentBased on 176 reviewsRead the reviews

Emanuele Zanda

Google review
Google

“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”

Read on Google

Giuseppe Ares Rosa

Google review
Google

“I had the chance to try the Opera cable blowing machine on site…”

Read on Google

Paolo Manna

Google review
Google

“I really enjoyed this course. It took place in a pleasant setting with friendly, helpful people.”

Read on Google

Stories from installers

See the difference on site.

Testimonial · Opera

“We cut our working time by 80%.”

Experience on site

“2 km of cable in half a day.”

Hear the results from the installers themselves. Watch their testimonials right here.

Product videos

Meet the machines.

Product overview

LADY

Product overview

GENIALE

Product overview

OPERA

Three machines. Find your fit.

Every installation is different.
Find your cable blowing machine.

Start with the job at hand. Our technician can answer your questions about the right setup.

01 / SHORT RUNSFibernet Lady cable blowing machine

Compact and lightweight

LADY

A compact, lightweight machine for short runs.

Cable diameter
1.2–10 mm
Duct diameter
5–16 mm
Pushing force
Up to 150 N
Maximum speed
80 m/min
Cable protection
Twin drive beltsrubber-coated
I’m interested in Lady
02 / LONG RUNSFibernet Opera pneumatic cable blowing machine

Pneumatic power

OPERA

A pneumatic machine for long cable runs.

Cable diameter
4–16 mm
Duct diameter
7–63 mm
Pushing force
Up to 900 N
Maximum speed
110 m/min
Cable protection
Twin drive beltsrubber-coated
I’m interested in Opera
03 / ELECTRIC DRIVEFibernet Geniale electric cable blowing machine

Electric, with two gears

GENIALE

For short and long runs. Two gears let you match force and speed to the job.

Cable diameter
1.2–8 mm
Duct diameter
5–16 mm
Pushing force
400 / 110 NGear 1 / Gear 2
Maximum speed
60 / 125 m/minGear 1 / Gear 2
Cable protection
Twin drive beltsrubber-coated
I’m interested in Geniale

Specifications for the Fibernet range. The speeds shown are maximum values. Actual results depend on installation conditions and machine setup.

Direct from the manufacturer

The machine matters.
Who supports you
matters even more.

When you’re working on site, you need practical answers. With Fibernet, you speak directly to the people who design and build your cable blowing machine.

Speak to a technician

Direct support

A specialist technician can help when you need it.

Spare parts available

Spare parts ready to ship, direct from the manufacturer.

Replacement machine

If your machine breaks down, a replacement may be available within 48 hours.

Check availability and terms with your technician.

Dedicated training

Get help making the most of your machine, from your very first job.

See it in action before you choose

Put it to the test.
On your own site.

Request a free hands-on demonstration on your site or at Fibernet’s test facility. Discuss a real job with the technician.

Request a free demonstration
An operator using an Opera cable blowing machine on site

Choose a cable blowing setup around your actual installation conditions

Choosing a drill powered optical fibre cable blowing machine starts with the cable and duct you intend to use, not with a headline speed figure. Contractors working on installation projects in Italy need equipment that suits the physical conditions of each route, including duct dimensions, cable construction, bends, gradients, and access arrangements. A machine that performs well on one route may require different settings or accessories on another. Before requesting a quotation, collect the cable outside diameter, duct internal and external diameters, planned section lengths, and the cable manufacturer’s handling limits. These details give the supplier a practical basis for assessing compatibility rather than relying on assumptions. Fibernet’s Italian manufacturing background provides a relevant starting point for companies seeking purpose-built cable blowing equipment and a direct discussion about their application. Founded in 2001, the company introduced its first cable blowing machine, Lady, in 2021, building on the technical experience of founder Giancarlo Trinei. For buyers evaluating a drill driven optical fibre cable blowing machine, the important questions concern how rotational input reaches the feeding mechanism, how the cable is guided, and how the operator controls the installation process. Ask which drill specifications are required, whether your intended drill is suitable, and which operating limits apply to the proposed configuration. Do not assume that every drill, cable size, or duct connection is interchangeable. Depending on the machine design and installation method, compressed air may still be required even when the feeding mechanism is drill powered. The drive source and the air supply serve different functions, so both must be assessed before equipment reaches the site. Discuss compressor requirements, air preparation, connection arrangements, and permissible pressure with the supplier, using the actual machine documentation as the reference. A useful enquiry should also describe how crews will position the machine, manage the cable reel, and communicate between access points. Restricted roadside working areas, uneven ground, and frequent changes between duct sections can affect the practicality of a setup as much as its nominal performance. Where several teams share equipment, straightforward adjustment procedures and clearly identified accessories become especially valuable. Evaluating an optical fibre cable blowing machine in this way helps purchasing staff and site supervisors agree on what the equipment must accomplish. Instead of selecting solely on purchase cost, they can compare suitability, preparation requirements, maintenance access, and support arrangements. Contact Fibernet with your installation data to establish which available configuration deserves closer technical evaluation, and request confirmation of specifications before committing to a purchase. This approach keeps the decision focused on dependable cable installation under your working conditions, without treating advertised performance as a guarantee for every duct route.

Turn site preparation into more controlled cable feeding

Reliable results with a drill powered optical fibre cable blowing machine depend on preparation, controlled operation, and a clear understanding of when to stop. Begin by checking the intended duct section using the project’s approved inspection and preparation procedures. Damaged connections, contamination, water, or an unexpected restriction can undermine an otherwise suitable machine setup. Confirm that the duct route is ready for installation and that all fittings used with compressed air are rated for the intended conditions. The receiving end must be managed safely, with personnel following the applicable site procedures for pressurized ducts and emerging cable. Before feeding begins, position the reel so the cable can leave it smoothly without unnecessary twisting or abrupt changes in direction. Keep the approach to the machine aligned and support the cable where necessary, while respecting the manufacturer’s minimum bend radius. Inspect the machine’s cable contact surfaces and guides, then fit the components specified for the cable and duct sizes in use. Feeding pressure or contact adjustment should follow the equipment instructions; excessive grip is not a substitute for resolving resistance elsewhere in the route. Operators comparing a drill powered fibre cable blowing machine with other configurations should pay particular attention to how speed is controlled during startup and how quickly feeding can be stopped. Start conservatively and observe the cable’s movement rather than immediately seeking the highest possible rate. Where compressed air is used, coordinate air and mechanical feeding in accordance with the machine instructions. Watch for changes in feed behavior, unusual noise, cable marking, or increasing resistance. These signs warrant assessment rather than simply applying more drive force. Cable construction, duct geometry, temperature, and route condition can all influence the outcome, so an installation plan should allow time for adjustments. A pneumatic optical fibre cable blowing machine may involve different drive controls and air demands, making a direct comparison meaningful only when the operating conditions and machine specifications are understood. Whatever the drive arrangement, cable handling limits remain essential. Keep a practical job record noting the installed section, cable and duct dimensions, equipment configuration, relevant settings, and any interruptions. This information can help supervisors identify recurring preparation issues and give the supplier useful evidence when technical assistance is needed. At the end of the operation, isolate energy sources and release pressure according to the equipment procedures before opening connections or carrying out cleaning. Inspect wear components and store accessories so the next crew can identify them easily. For projects in Italy, a repeatable preparation checklist can make equipment handovers clearer across different sites and teams. Fibernet can be contacted to discuss the proposed application and clarify the documentation, compatible components, and assistance available for the equipment under consideration.

Evaluate Italian manufacturing, ownership costs, and support

A purchasing decision should account for what happens after delivery, especially when the same machine will move between multiple crews or installation sites. A drill powered optical fibre cable blowing machine needs to be assessed as part of a working equipment package: machine, compatible drive tool, required duct fittings, cable guides, air connections where applicable, and the consumable or wear components specified by the manufacturer. Request a written breakdown of what is included and what must be supplied separately. This prevents a seemingly complete quotation from leaving important site requirements unresolved. When comparing optical fibre cable blowing machine price, distinguish the initial equipment cost from the broader cost of ownership. Relevant factors include accessory coverage, maintenance requirements, availability of replacement parts, transport arrangements, and the time needed to restore equipment to service if a problem occurs. Avoid assigning a financial benefit to higher speed unless the proposed machine has been evaluated against comparable cable, duct, and route conditions. A useful commercial conversation connects the quoted configuration to the tasks your crews actually undertake. Fibernet combines a family-led company history with Italian product development. Its founder’s technical background reaches back to early cable installation work in Italy during the 1980s, while the next generation joined the business beginning in 2010. The launch of Lady in 2021 marked a specific step into cable blowing machinery. These facts provide company context, but buyers should still request current product documentation and confirmation of the configuration offered. For customers purchasing for use in Italy, clarify delivery arrangements, documentation language, applicable conformity information, and the procedure for requesting technical help. Fibernet’s made-in-Italy products are supported by assistance in the United States and worldwide; confirm the contact channels, service location, parts logistics, and response arrangements relevant to your operating area before ordering. International availability of assistance should not be interpreted as a promise of identical service times in every location. If project duration is uncertain, optical fibre cable blowing machine rental may also enter the commercial comparison, but rental availability and terms must be checked rather than assumed. Compare any temporary-use proposal with purchasing on equivalent accessory coverage, support, damage responsibility, and transport costs. For an owned machine, ask how replacement wear items are identified and what information the support team needs when troubleshooting. Keeping the serial number, equipment configuration, photographs, and a concise description of the installation conditions available can make enquiries more productive. The goal is a purchasing decision that remains workable beyond the first installation. Send Fibernet your cable dimensions, duct specifications, anticipated workload, and operating location to request a configuration discussion and a quotation grounded in your actual cable blowing requirements.

Still looking for information about drill powered optical fibre cable blowing machine?

Fill out the form and discover what Fibernet Srl can do for you!

Contact us!

Before you get started

Have a question?
Start here.

If you prefer, speak to us directly.

+39 346 652 9915
Which cable blowing machine is right for my site?

Compare the cable diameter, duct diameter and installation distance. Lady is compact and lightweight for short runs. Opera is pneumatic and designed for long runs. Geniale is electric and handles both. A Fibernet technician can help you choose.

Can I see the machine in action before I buy it?

Yes. You can request a free hands-on demonstration on your site or at Fibernet’s test facility. Tell us what you need in the form and a technician will arrange it with you. Request a demonstration.

How much does a Fibernet cable blowing machine cost?

To get a price, contact a Fibernet advisor using the form or call +39 346 652 9915.

What support will I get after purchase?

Fibernet offers direct technical support, spare parts ready to ship and dedicated training. If your machine breaks down, a replacement may be available. Ask your technician about availability and terms.

Your next project
starts with the right choice.

Tell us about your job. We’ll help you find the right cable blowing machine.

CallRequest information