Emanuele Zanda
Google reviewRead on Google“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”
Cable blowing machines · Made in Italy
From last-mile connections to long-distance runs, a Fibernet technician can help you choose the right machine for your fiber optic cable installation.
Opera, image 1 of 3
Expert advice direct from the manufacturer / Free demonstration on request
Some of our customers.






Keep your installation moving with Fibernet cable blowing machines.
Photos and stories from installers, published by Fibernet.






Read on Google“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”
Read on Google“I had the chance to try the Opera cable blowing machine on site…”
Read on Google“I really enjoyed this course. It took place in a pleasant setting with friendly, helpful people.”
Stories from installers
Hear the results from the installers themselves. Watch their testimonials right here.
Product videos
Three machines. Find your fit.
Start with the job at hand. Our technician can answer your questions about the right setup.

Compact and lightweight
A compact, lightweight machine for short runs.

Pneumatic power
A pneumatic machine for long cable runs.

Electric, with two gears
For short and long runs. Two gears let you match force and speed to the job.
Specifications for the Fibernet range. The speeds shown are maximum values. Actual results depend on installation conditions and machine setup.
Direct from the manufacturer
When you’re working on site, you need practical answers. With Fibernet, you speak directly to the people who design and build your cable blowing machine.
Speak to a technicianA specialist technician can help when you need it.
Spare parts ready to ship, direct from the manufacturer.
If your machine breaks down, a replacement may be available within 48 hours.
Check availability and terms with your technician.Get help making the most of your machine, from your very first job.
See it in action before you choose
Request a free hands-on demonstration on your site or at Fibernet’s test facility. Discuss a real job with the technician.
Request a free demonstration
Selecting a drill driven OFC cable blowing machine starts with the installation you need to complete, not with an isolated speed figure. Cable outside diameter, duct internal diameter, route geometry, and the condition of the installed pathway all influence whether a proposed configuration is suitable. For American contractors evaluating Italian-made equipment, these details provide a practical starting point for a discussion with Fibernet. Share the cable manufacturer's installation limits, the duct specifications, and the approximate route length before requesting a recommendation. Include known bends, changes in elevation, intermediate access points, and any uncertainty about duct continuity. This information helps make the equipment conversation specific to the work rather than dependent on assumptions. A drill driven cable blowing machine combines mechanical feeding with compressed air, but the relationship between those elements must remain within the instructions for the selected equipment and cable. The drill supplies mechanical input; it does not replace the compressor. Air availability therefore deserves the same attention as drive compatibility. Ask which compressor pressure and airflow are required for the proposed configuration, what connection arrangements are needed, and which cable and duct sizes the machine supports. Do not assume that a drill, compressor, or fitting already available on a truck will automatically be suitable. The feed interface also matters because the cable must be advanced without exceeding its allowable mechanical limits. Before installation, operators should check that the selected guides, seals, and gripping components match the actual cable and duct. Incorrect sizing can compromise sealing, impair traction, or expose the cable to unnecessary stress. A cable blowing machine for fiber optic cable installation should therefore be evaluated as part of a complete working arrangement rather than as a standalone purchase. Duct preparation is equally important. Confirm continuity using an approved procedure, check for obstructions, and establish whether cleaning, drying, or a compatible lubricant is appropriate. Follow the duct, cable, and machine manufacturers' requirements instead of treating lubrication as a universal remedy for difficult conditions. At the worksite, prepare a stable equipment position and an orderly cable payoff arrangement that avoids sharp entry angles and uncontrolled reel movement. Establish clear communication between the machine operator and anyone supervising access points or the cable supply. Fibernet's Italian manufacturing identity is relevant here because purchasing decisions should connect product origin with the technical information needed to operate responsibly. Request confirmation of the applicable model, supplied components, operating documentation, and assistance arrangements before ordering. The result is a better-defined equipment choice, with fewer unanswered questions when the crew reaches the duct entrance and begins preparing the blowing operation.
On an active jobsite, a successful blowing operation depends on preparation, observation, and the ability to stop when conditions change. A drill driven OFC cable blowing machine should be introduced into a documented workflow that follows the operating manual and the cable manufacturer's limits. Begin by establishing who controls the drive, who monitors the cable supply, and how the crew will communicate an immediate stop. Keep the area around the cable entry organized so that loose materials, hoses, and moving equipment do not interfere with the operation. Before introducing compressed air, inspect connections and verify that the duct attachment and sealing components are installed as instructed. Never loosen a pressurized connection, and follow the prescribed isolation and depressurization procedure before adjustments. For a drill powered cable blowing machine, drill suitability is another checkpoint, not an assumption. Confirm the permitted operating mode, coupling arrangement, and speed or torque guidance with the supplier for the specific model. Avoid improvised adapters or operating settings that have not been approved. The objective is controlled cable movement, not simply the highest available drill speed. Cable payoff deserves continuous attention throughout the run. Excessive reel resistance, tangles, or an unsuitable entry angle can create problems before the cable reaches the duct. Position the reel appropriately, respect the minimum bending radius, and prevent the cable from rubbing against unsuitable surfaces. As the operation progresses, watch for changes in feeding behavior and follow the machine instructions for responding to resistance. If progress becomes irregular, stop and investigate rather than increasing force without understanding the cause. Possible explanations include a duct obstruction, leakage, an unsuitable seal, cable supply resistance, or route conditions that differ from the original plan. These are diagnostic possibilities, not a substitute for the manufacturer's troubleshooting procedure. Contractors comparing a drill driven cable jetting machine should also consider how easily the proposed equipment can be prepared for their actual sequence of jobs. Ask about component changes between supported sizes, inspection points, cleaning requirements, and the recommended spare components for routine site readiness. Any claimed time saving should be assessed against comparable working conditions, including duct preparation and setup, rather than against an unexplained maximum performance figure. Record useful installation information after each run: equipment configuration, cable and duct dimensions, route characteristics, operating observations, and any interruptions. Such records can help the next crew understand what happened and give technical support a clearer basis for advice. For American teams purchasing equipment made in Italy, this disciplined approach also makes remote communication more effective. Fibernet can receive a more useful inquiry when the contractor provides specific observations instead of a general statement that the cable will not advance. Confirm available assistance in the United States and worldwide, including contact procedures and any applicable service conditions, before equipment is deployed.
Fibernet's approach to blowing equipment comes from a technical background that predates the company's establishment in 2001. Founder Giancarlo Trinei worked with early optical cable installations in Italy during the 1980s, including installation and testing activities associated with the country's first submarine cable connections. That experience provides context for a business focused on practical equipment and the challenges faced by installation professionals. In 2021, Fibernet introduced its first cable blowing machine, Lady, marking an important step in the development of its blowing equipment range. Buyers considering a drill driven OFC cable blowing machine should use this background as the beginning of a technical conversation, while still requesting current specifications for the exact product being proposed. Company history does not replace a compatibility check, and the name of a product alone does not establish which cable sizes, duct sizes, or drive arrangements it supports. A useful purchasing inquiry describes both the immediate project and the contractor's expected workload. Explain whether the equipment will be assigned to a single crew or moved between teams, which cable and duct combinations occur most often, and what compressed air resources are available. If you are evaluating a drill driven fiber cable blowing machine, ask Fibernet to identify the relevant configuration and clarify what is included in the quotation. Distinguish the main unit from optional accessories, size-specific components, and items that must be supplied separately. This makes offers easier to evaluate without assuming that every installation requirement is covered by a headline price. The same care applies when requesting information about a drill driven fibre optic cable blowing machine through an international purchasing process. Terminology can vary between markets, so dimensions, connection details, and written specifications should take priority over product descriptions alone. Request clear documentation covering operation, inspection, maintenance, and the limits of intended use. For American customers, Italian-made equipment should be accompanied by a clear understanding of assistance in the United States and worldwide. Ask how to submit technical questions, what information is needed for troubleshooting, and how replacement components or service requests are handled for your location. Confirm current availability, delivery arrangements, warranty terms, and any service exclusions directly with the company rather than assuming a particular turnaround time. Fibernet remains a family business whose generational transition began in 2010 with the involvement of Matteo, Marta, and Ismael. That continuity gives context to its ambition to build an international presence while retaining its Italian identity. For the buyer, however, the decisive outcome remains practical: equipment matched to the installation, an understandable supply scope, and a support route established before work begins. Explore the company website and contact Fibernet with your project details to move from a broad product search to a properly defined equipment discussion.
Fill out the form and discover what Fibernet Srl can do for you!
Contact us!Before you get started
If you prefer, speak to us directly.
+39 346 652 9915Compare the cable diameter, duct diameter and installation distance. Lady is compact and lightweight for short runs. Opera is pneumatic and designed for long runs. Geniale is electric and handles both. A Fibernet technician can help you choose.
Yes. You can request a free hands-on demonstration on your site or at Fibernet’s test facility. Tell us what you need in the form and a technician will arrange it with you. Request a demonstration.
To get a price, contact a Fibernet advisor using the form or call +39 346 652 9915.
Fibernet offers direct technical support, spare parts ready to ship and dedicated training. If your machine breaks down, a replacement may be available. Ask your technician about availability and terms.
Tell us about your job. We’ll help you find the right cable blowing machine.