Emanuele Zanda
Google reviewRead on Google“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”
Cable blowing machines · Made in Italy
From last-mile connections to long-distance runs, a Fibernet technician can help you choose the right machine for your fiber optic cable installation.
Opera, image 1 of 3
Expert advice direct from the manufacturer / Free demonstration on request
Some of our customers.






Keep your installation moving with Fibernet cable blowing machines.
Photos and stories from installers, published by Fibernet.






Read on Google“An excellent experience on the installer training course. The whole team was professional and knowledgeable.”
Read on Google“I had the chance to try the Opera cable blowing machine on site…”
Read on Google“I really enjoyed this course. It took place in a pleasant setting with friendly, helpful people.”
Stories from installers
Hear the results from the installers themselves. Watch their testimonials right here.
Product videos
Three machines. Find your fit.
Start with the job at hand. Our technician can answer your questions about the right setup.

Compact and lightweight
A compact, lightweight machine for short runs.

Pneumatic power
A pneumatic machine for long cable runs.

Electric, with two gears
For short and long runs. Two gears let you match force and speed to the job.
Specifications for the Fibernet range. The speeds shown are maximum values. Actual results depend on installation conditions and machine setup.
Direct from the manufacturer
When you’re working on site, you need practical answers. With Fibernet, you speak directly to the people who design and build your cable blowing machine.
Speak to a technicianA specialist technician can help when you need it.
Spare parts ready to ship, direct from the manufacturer.
If your machine breaks down, a replacement may be available within 48 hours.
Check availability and terms with your technician.Get help making the most of your machine, from your very first job.
See it in action before you choose
Request a free hands-on demonstration on your site or at Fibernet’s test facility. Discuss a real job with the technician.
Request a free demonstration
Choosing a drill driven fibre optic cable blowing machine starts with the cable and duct combination, not simply the drive system. For contractors installing cable into previously laid ducts, the practical objective is controlled advancement without exposing the cable to excessive mechanical stress. A drill supplies the mechanical input to a compatible feeding mechanism, while compressed air supports cable movement through the duct. These functions work together, but their effectiveness depends on correct equipment selection, suitable operating settings, and the condition of the route. Before specifying a machine, establish the cable diameter, duct internal diameter, cable construction, and installation requirements stated by the cable manufacturer. A close dimensional match alone does not prove compatibility. Cable stiffness, jacket material, duct geometry, and available airflow also influence whether the proposed arrangement is appropriate. Fibernet provides a manufacturer contact point for discussing these requirements before an equipment decision is made. Founded in Italy in 2001, the company brings a technical background rooted in founder Giancarlo Trinei's experience with early Italian cable installations. Its cable blowing machine development reached an important milestone in 2021 with the introduction of Lady. That history provides context for a product discussion, rather than a substitute for checking the specifications of the particular machine being considered. When evaluating a drill powered fibre optic cable blowing machine, ask which drill characteristics are permitted, how the drive connects, and what operating limits apply. Do not assume that any cordless drill is suitable or that drill torque should be set to its maximum. The correct arrangement must follow the equipment instructions and account for the cable's allowable pushing load. Equally important is the compressed air supply. Compressor pressure and airflow are separate specifications, and both must be checked against the chosen equipment and installation conditions. Hoses, connectors, and air treatment requirements should be reviewed as part of the complete setup. For projects in Italy and American contracting operations, documenting these details before mobilization helps crews avoid discovering incompatible components at the duct entry point. A cable blowing machine for fiber optic cable installation should therefore be assessed as part of a working system, including its required accessories, cable guidance, duct connection, and maintenance provisions. Contact Fibernet through its website with the relevant dimensions and route information to discuss suitable options. Italian manufacturing, together with assistance in the United States and worldwide, connects product selection with the practical questions that arise before and during field use. Request confirmation of the configuration, included components, and applicable documentation so your purchasing decision rests on defined requirements rather than assumptions about performance.
A successful blowing operation begins before the drill is engaged. The crew needs a clear understanding of the duct route, access points, anticipated bends, and any changes in duct size or material. Inspect the entry area and arrange the equipment so that cable can approach the feeding mechanism without sharp deflections or unnecessary drag. The cable supply must pay out smoothly, with suitable handling arrangements that prevent twists and uncontrolled movement. Protecting this approach path matters because resistance outside the duct can undermine an otherwise well prepared installation. Duct preparation deserves the same attention. Follow the approved project procedures for checking continuity, cleanliness, and integrity, and confirm that connections can withstand the intended operating conditions. Contamination, water, damaged sections, and leaking joints can interfere with airflow or increase friction. A drill driven fibre optic cable blowing machine cannot compensate for every defect in the pathway, so unresolved problems should be addressed before attempting to increase feed effort. For a compressed air fibre optic cable blowing machine, the air circuit must be treated as a safety critical part of the setup. Inspect hoses and couplings, secure connections as required, and use components rated for the specified pressure. Isolate and depressurize the system before opening connections or adjusting components where the instructions require it. The work area should also accommodate compressor noise, hose routing, and safe access for the people supervising the operation. Once the route and equipment are ready, configure the cable guides, seals, and drive contact according to the manufacturer's instructions. Excessive clamping force may damage a cable jacket, while insufficient contact may cause slippage. Neither problem should be addressed through guesswork. Check the allowable cable loads and the machine's adjustment procedure, then begin in a controlled manner while observing cable movement and the behavior of the setup. During installation, the operator should watch for changes rather than relying on a fixed expectation of speed or distance. Unexpected resistance, irregular feeding, or a change in cable behavior warrants investigation. Stop and assess the likely cause instead of assuming that more drill torque or air pressure will resolve it safely. A pneumatic fibre optic cable blowing machine and a drill driven arrangement may differ in their drive systems, but both require disciplined attention to the relationship between feed force, airflow, and route conditions. Record the equipment configuration and relevant operating observations for each job. These notes can improve planning for comparable routes without turning one successful result into a universal performance promise. Fibernet's assistance in the United States and worldwide provides a channel for discussing equipment questions, while the applicable manual and project safety procedures remain essential references for the crew.
The value of a drill driven fibre optic cable blowing machine is best assessed across the work it must perform, the accessories it requires, and the support available after delivery. A purchase price becomes meaningful only when the proposed configuration is clear. Ask for a written quotation identifying the machine, compatible cable and duct sizes, supplied components, required external equipment, and any optional items relevant to your projects. This makes it easier to compare proposals on an equivalent basis rather than treating differently equipped packages as interchangeable. When researching fibre optic cable blowing machine price, include the practical costs of preparing a usable installation setup. Depending on the configuration, these may involve a suitable drill, compressor capacity, hoses, connectors, seals, guides, or other application specific components. Confirm which items are included and which must be sourced separately. Also ask about delivery arrangements, documentation, maintenance requirements, and the process for obtaining replacement wear parts. None of these questions requires an assumption about a particular machine's features; each helps establish what the supplier is actually offering. Fibernet's identity combines Italian manufacturing with a family business history and an ambition to serve contractors internationally. Founder Giancarlo Trinei brought experience from the early development of cable installations in Italy, and the company began its generational transition in 2010 with Matteo, Marta, and Ismael joining the business. For buyers, the useful connection is between that technical heritage and a direct discussion of present equipment needs. The made in Italy origin is part of the product proposition, while assistance in the United States and worldwide addresses the realities of customers working beyond Italy. Support expectations should nevertheless be defined before ordering. Ask how technical enquiries are handled, what information should accompany a troubleshooting request, and how parts availability is confirmed for your location. If you are also considering a used fibre optic cable blowing machine, examine its condition and completeness with equal care. Wear in the feeding components, damaged seals, missing adapters, or an undocumented service history can change the overall value of an apparently inexpensive purchase. Verify the exact model and configuration, obtain the relevant instructions, and establish whether replacement components remain obtainable. Do not assume that a previously successful setup will suit a different cable and duct combination. For American contractors purchasing Italian equipment, and for projects carried out in Italy, clear technical communication is more useful than broad claims about universal suitability. Send Fibernet your cable specifications, duct dimensions, expected route conditions, and intended operating setup. Request a discussion of the available equipment and assistance arrangements through www.fibernetsrlusa.com so the next step is based on your installation requirements, not an unsupported estimate of speed, distance, or savings.
Fill out the form and discover what Fibernet Srl can do for you!
Contact us!Before you get started
If you prefer, speak to us directly.
+39 346 652 9915Compare the cable diameter, duct diameter and installation distance. Lady is compact and lightweight for short runs. Opera is pneumatic and designed for long runs. Geniale is electric and handles both. A Fibernet technician can help you choose.
Yes. You can request a free hands-on demonstration on your site or at Fibernet’s test facility. Tell us what you need in the form and a technician will arrange it with you. Request a demonstration.
To get a price, contact a Fibernet advisor using the form or call +39 346 652 9915.
Fibernet offers direct technical support, spare parts ready to ship and dedicated training. If your machine breaks down, a replacement may be available. Ask your technician about availability and terms.
Tell us about your job. We’ll help you find the right cable blowing machine.